metallographhic supplies, metallographicsupplies.com abrasive cutoff, cut-off wheels cold, hot, mounting, molding powders abrasive, SiC, aluminum oxide discs diamond polishing suspensions, polishing cloths
cold, hot, mounting, molding powders abrasive, SiC, aluminum oxide discs diamond polishing suspensions, polishing cloths
metallographhic supplies, metallographicsupplies.com abrasive cutoff, cut-off wheels

 
COLD MOUNTING Metlab Epoxy, Jetset Epoxy, Technovit 4000, Polyester Kit, Fast Cure Acrylic, Glass Filled Curing Acrylic

sectioning mounting grinding polishing
 

METLAB EPOXY COLD MOUNTING

METLAB EPOXY is a low viscosity, two component clear casting resin. METLAB gels rapidly at room temperature and cures to a clear tough chemical resistant compound. It has excellent adhesion to most substrates as well as a good electrical insulator. Uses include encapsulating, potting metallographic or similar specimens, and potting as electronic devises. Mix 15 parts (by volume) of METLAB resin with 2 parts (by volume) of METLAB hardener. A 100 gram mass will gel in 20 min. at 23 degrees C. Cure time will depend on temperature and mass of the resin. 4-8 hours at room temperature is usually sufficient. Can be used with vacuum impregnation. Shore D hardness of 82

COLD MOUNTING Metlab Epoxy, cold mounting
Click here Purchase or Samples

METLAB EPOXY COLD MOUNTING

Catalog # Metlab Epoxy Cold Mounting Qty
M135 1 Quart Resin, 1/2 Pint Hardener
(10) 7 oz. waxed cups (10) stir sticks
KIT
M136 Metlab Epoxy Resin QUART
M137 Metlab Epoxy Resin GALLON
M138 Metlab Epoxy Hardener PINT
M139 Metlab Epoxy Hardener QUART
Metlab  Epoxy Cold Mounting

 

JETSET EPOXY COLD MOUNTING

JETSET EPOXY is a low viscosity, two component clear casting resin. JETSET gels rapidly at room temperature and cures to a clear tough chemical resistant compound. It has excellent adhesion to most substrates as well as a good electrical insulator. Uses include encapsulating, potting metallographic or similar specimens and potting as electronic devices. Mix 2 parts (by volume) of resin with I part (by volume) of hardener. Mix thoroughly. Entrapped air can be minimized by gentle yet thorough stirring. Air cure to full hardness in 30 min.

CO

LD MOUNTING Jetset Epoxy, cold mounting

Click here Purchase or Samples

JETSET EPOXY COLD MOUNTING

Catalog # Jetset Epoxy Cold Mounting Qty
M135A 1 Quart Resin, 1/2 Pint Hardener
(10) 7 oz. waxed cups (10) stir sticks
KIT
M136A Jetset Epoxy Resin QUART
M137A Jetset Epoxy Resin GALLON
M138A Jetset Epoxy Hardener PINT
M139A Jetset Epoxy Hardener GALLON
Jetset Epoxy Cold Mounting

 

FAST CURE ACRYLIC COLD MOUNTING

FAST CURE ACRYLIC is fast curing translucent two component acrylic casting system. Specimens may usually be removed after 5-10 min. at room temperature. Fast cure acrylic is characterized by an unusually high standard of adhesion for this type of system. It also exhibits relatively low shrinkage and good flow characteristics. Mix 2 parts (by volume) of Fast cure acrylic powder with 1 part (by volume of Fast cure acrylic liquid. Stir thoroughly for 15-20 sec. And use immediately. Material will cure in 5-10 min. at room temperature. Shore D hardness 80.

COLD MOUNTING Fast Cure Acrylic, cold mounting

Click here Purchase or Samples

FAST CURE ACRYLIC COLD MOUNTING

Catalog # Fast Cure Acrylic Cold Mounting Qty
M140 1 Lb. Powder, 1 Pint Liquid
(10) 7 oz. waxed cups (10) stir sticks
KIT
M142 Fast Cure Acrylic Powder 5 LBS.
M143 Fast Cure Acrylic Powder 10 LBS.
M145 Fast Cure Acrylic Liquid GALLON
M146 Fast Cure Acrylic Liquid GALLON
Fast Cure Acrylic Cold Mounting

 

GLASS FILLED CURING ACRYLIC COLD MOUNTING

GLASS FILLED CURING ACRYLIC Same as our Fast Cure Acrylic but exhibits a higher hardness with excellent edge retention with minimal shrinkage. Shore D Hardness 95. Color is opaque black

COLD MOUNTING Glass Filled Curing Acrylic, cold mounting









Click here Purchase or Samples

GLASS FILLED CURING ACRYLIC COLD MOUNTING

Catalog # Glass Filled Curing Acrylic Cold Mounting Qty
M140G 1 Lb. Powder, 1 Pint Liquid
(10) 7 oz. waxed cups (10) stir sticks
KIT
M142G Glass Filled Curing Acrylic Powder 5 LBS.
M143G Glass Filled Curing Acrylic Powder 10 LBS.
M145G Glass Filled Curing Acrylic Liquid GALLON
M146G Glass Filled Curing Acrylic Liquid GALLON
Glass Filled Curing Acrylic Cold Mounting

 

POLYESTER KIT COLD MOUNTING

POLYESTER is a clear, two component room temperature curing casting resin. Mix 1 gram of catalyst cat # M149 with each 60 grams of Polyester cat # M148 ( in ounces it is 0.01 oz. Of catalyst to 6 oz. of resin ) stir thoroughly to ensure proper mixing. Blend slowly to avoid trapping bubbles. Mix for 1 min. the resin will turn a slight greenish color upon mixing. This color will disappear when the resin cures. Cure time varies with mass and temperature. Smaller masses and lower temperatures result in longer cure times. For 100g mass at 72 degrees F gel time is approx. 1 hour. Parts can usually be demolded after 1-1/2 - 2 hours. Ultimate properties are obtained after 8-10 hours. Cure time may be shortened by using mild heat. Shore D hardness of 76

COLD MOUNTING Polyester Kit, cold mounting
Click here Purchase or Samples

POLYESTER KIT COLD MOUNTING

Catalog # Polyester Kit Cold Mounting Qty
M147 1 Quart Resin, Unit Hardener
(10) 7 oz. waxed cups (10) stir sticks
KIT

Polyester Kit Cold Mounting

 

TECHNOVIT 4000 COLD MOUNTING

TECHNOVIT 4000 (POLYESTER)is a fast polymerizing cold curing three-component resin based on modified polyester supplied as powder, syrup I and syrup II. It is suitable for gap-free embedding of specimen that are difficult to embed because of their shape or coating, that cannot be exposed to high temperature or pressure which requires fast and accurate testing and for which the embedding material must be abrasion-resistant. Color is white mixing ratio is 2:2:1 processing time is 4 min. curing time at 22 degrees C is 7 min.

COLD MOUNTING Technovit 4000, cold mounting
Click here Purchase or Samples

TECHNOVIT 4000 COLD MOUNTING

Catalog # Technovit 4000 Cold Mounting Qty
M140G 750 g powder, 500 ml syrup I, 250 ml syrup II KIT
Technovit 4000 COLD MOUNTING

 

 
COLD MOUNTING Metlab Epoxy, Jetset Epoxy, Technovit 4000, Polyester Kit, Fast Cure Acrylic, Glass Filled Curing Acrylic
Other Sample Preparation Websites
Charpy Notch Machines Hardness Testers Image Analysis Metallographic Consumables
charpy,izod,hand,operated,spare,parts,csm,cnb,variable,equipment

semi automatic hardness tester

semi automatic hardness tester metallurgical, metallographic, metallography sample preparation concumables
  Metallographic supplies include cold mounting metlab epoxy, jetset epoxy, technovit 4000, polyester kit, fast cure acrylic, glass filled curing acrylic
sectioning mounting grinding polishing
    4011 Hyde Park Blvd  -  P.O. Box 1075  -  Niagara Falls, NY 14302  - 1-800-828-6866